Installation Instructions:
SPECIFICATIONS:
Before placing the machine in position, prepare the electrical, water and drainage connections. Final connections can then be made when the machine is pushed into position. Hot and Cold washing machine stop taps should be situated above or next to the machine either to the left or right in an accessible position. The machine is supplied with the water inlet pipes already fitted. They are cross-linked polythene pipes (PEX), fitted with a ¾” BSP internal threaded connector. The pipe can be bent as required: take care, however, not to kink it.
DRAINAGE CONNECTION
The machine is supplied with the outlet hose connected.
Run the outlet hose into top of 38mm or 50mm standing waste.
Drain outlet hose to be 400mm above bottom of door.
Top of standing waste to be 1000mm from floor.
LEVELING
Adjust levelling feet of the machine to allow unit to sit square
PUSH THE MACHINE INTO POSITION:
When all connections for power supply, water and drainage are ready, push the machine into position, taking up the slack in the outlet hose and supply pipes at the same time. This prevents kinks from being formed in the hose or pipes. Re adjust levelling feet.
STARTING MACHINE FOR THE FIRST TIME:
Once the machine has been connected to the power outlet, water connection and turned on: ‘Utensils’ will appear on the Control Panel.
The Control panel will then read ‘D’ and ‘Utensils’.
‘D’ is displayed on the Control Panel indicating that the detergent has not yet been connected. Connection of detergent is done by referring to page 7 of the Use and Care Guide.
Once the detergent has been connected and primed into the machine the Control Panel will read ‘Utensils’. The machine is ready for normal use.
Please call if you require further consultation.
SANITECH AUSTRALIA
Tel: 61 3 9809 2701 Mob: 0427 823 574
- Height 1540 mm
- Width 600 mm
- Depth (closed) 610 mm
- Depth (open) 1200 mm
- Hot Water 20mm BSP, 50kPa min WM stop tap. Suggested temperature of hot water supply 60C.
- Electrical 240V, 50Hz 10 Amp.
- Drain hose outlet Minimum 38mm standing waste.
Before placing the machine in position, prepare the electrical, water and drainage connections. Final connections can then be made when the machine is pushed into position. Hot and Cold washing machine stop taps should be situated above or next to the machine either to the left or right in an accessible position. The machine is supplied with the water inlet pipes already fitted. They are cross-linked polythene pipes (PEX), fitted with a ¾” BSP internal threaded connector. The pipe can be bent as required: take care, however, not to kink it.
DRAINAGE CONNECTION
The machine is supplied with the outlet hose connected.
Run the outlet hose into top of 38mm or 50mm standing waste.
Drain outlet hose to be 400mm above bottom of door.
Top of standing waste to be 1000mm from floor.
LEVELING
Adjust levelling feet of the machine to allow unit to sit square
PUSH THE MACHINE INTO POSITION:
When all connections for power supply, water and drainage are ready, push the machine into position, taking up the slack in the outlet hose and supply pipes at the same time. This prevents kinks from being formed in the hose or pipes. Re adjust levelling feet.
STARTING MACHINE FOR THE FIRST TIME:
Once the machine has been connected to the power outlet, water connection and turned on: ‘Utensils’ will appear on the Control Panel.
The Control panel will then read ‘D’ and ‘Utensils’.
‘D’ is displayed on the Control Panel indicating that the detergent has not yet been connected. Connection of detergent is done by referring to page 7 of the Use and Care Guide.
Once the detergent has been connected and primed into the machine the Control Panel will read ‘Utensils’. The machine is ready for normal use.
Please call if you require further consultation.
SANITECH AUSTRALIA
Tel: 61 3 9809 2701 Mob: 0427 823 574